Car keys · Wexford
Ignition Lock Repair in Wexford
After a slushy week the key barely reaches accessory before it stalls, gritty and reluctant, where it used to move cleanly through every position.
In plain words
Winters here add road grit, salt and moisture to the list of things an ignition barrel deals with, on top of ordinary wear from years of daily use. A barrel that has gone stiff or gritty through a cold, slushy season is cleaned, serviced and lubricated rather than simply forced, and the fix holds up through the next stretch of the same weather.
How the visit goesThe key slides in fine and turns without any resistance at all, and the dash lights flicker, but nothing catches. No click, no crank, just a key spinning loosely in a slot that used to grab hold of it properly.
Ignition Lock Repair
How the visit goes
Looking for signs of an earlier attempt
Scratches around the slot, a loose-feeling housing, or a barrel that spins without any of the usual resistance can mean somebody already tried the lock before the locksmith arrived. Noting this before starting matters for two reasons: it changes the repair, since a lock that has been forced usually needs full replacement rather than a simple service, and it gives the owner an honest account of what was already there rather than what happened during this particular visit.
Servicing the cylinder in place first
The first option is always the least invasive one: cleaning out the keyway, freeing a wafer that has stuck in a raised position, and lubricating the mechanism so the existing cylinder goes back to turning the way it should. This keeps the original hardware on the vehicle and avoids cutting a new key altogether when the fault turns out to be wear or contamination rather than a broken part. Only when this fails to restore normal behaviour does the barrel come out of the column.
One key doing everything it did before
If the doors and trunk already shared a key with the ignition, that arrangement is preserved or restored wherever the vehicle's design allows it, so the same key you carry now still opens everything it used to open before. Where a new key was cut, it is tested in every lock on the vehicle before the visit is called finished, not only in the ignition itself, so a lock quietly left out never becomes tomorrow's surprise.
Ignition Lock Repair
In the van
Key code reader
Ignition lock cylinder
Pick and tension tools
Plug follower
Keyed-alike pinning kit
Ignition Lock Repair
What affects the quote
Access through the steering column
Reaching some ignition cylinders means removing trim, shrouding or fasteners around the column first, and putting all of it back cleanly afterward. A column that is straightforward to open takes less time than one that is not.
Age and history of the vehicle
An older vehicle may have hardware that is harder to source, or wear built up over many years of daily use, while a vehicle with a known repair history gives the locksmith a clearer starting point.
Whether an electronic diagnosis is also needed
When the mechanical repair alone does not account for everything the vehicle is doing, checking the immobilizer or transponder side becomes a separate task, priced and scoped apart from the lock cylinder itself.
What to have ready
- Would you like extra keys cut during the same visit?
- Are any warning or immobilizer lights showing on the dash?
- Is the key stuck and unable to be removed?
Ignition Lock Repair: questions
QuestionsWhat information should I have ready when I call?
The vehicle's year, make and model, and exactly what the key does: whether it inserts, turns, engages anything, or is stuck. Mention whether a spare key exists, whether anything has already been tried on the lock, and whether the vehicle's warning lights or dash behave normally otherwise. Having the vehicle permit or registration nearby helps the ownership check move along smoothly.
What if there are scratches or damage around my ignition slot already?
That is noted honestly before any work begins, since it often means an earlier attempt was made on the lock. Damage like this usually points toward a full cylinder and housing replacement rather than a simple service, because the internal parts of a lock that has already been forced are rarely trustworthy afterward. You are shown what was found before deciding how to proceed together.
Do you also program the chip or transponder in the key?
Ignition lock repair covers the mechanical cylinder itself, the part a key physically turns. Transponder programming and immobilizer resets are a separate electronic step that some vehicles need alongside a mechanical repair and some do not. Where that separate step turns out to be necessary, it is named clearly and scoped as its own piece of work rather than folded into the mechanical visit.
Related services
- Car Key ReplacementMinus twenty outside, the fob button does nothing, and the door keyhole has a crust of road salt over it because you have not used a metal key in that car since the day you bought it.
- Spare Car Key DuplicationA lockout last month ended with a locksmith opening the door and going home, and the same single key has been carried ever since with nothing behind it.
- Key Fob ProgrammingButtons on the fob still light up and the remote still clicks, but the vehicle refuses to start even with the fob sitting in the cupholder.